Cisco dumpskey ccnp Enterprise 300-410 Full Course Free by Elsa q530 vce pdf

Page: 20 / 47

Exam Name:	Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI)
Exam Code:	300-410 Dumps
Vendor:	Cisco	Certification:	CCNP Enterprise
Questions:	630 Q&A's	Shared By:	elsa

Question 80

Refer to the exhibit.

Questions 80

BGP and EIGRP are mutually redistributed on R3, and EIGRP and OSPF are mutually redistributed on R1. Users report packet loss and interruption of service to applications hosted onthe 10.1.1.0724 prefix. An engineer tested the link from R3 to R4 with no packet loss present but has noticed frequent routing changes on R3 when running the debug ip route command. Which action stabilizes the service?

Options:

Tag the 10.1.1.0/24 prefix and deny the prefix from being redistributed into OSPF on R1.

Repeat the test from R4 using ICMP ping on the local 10.1.1.0/24 prefix, and fix any Layer 2 errors on the host or switch side of the subnet. ^ C. Place an OSPF distribute-list outbound on R3 to block the 10.1.10/24 prefix from being advertised back to R3.

Reduce frequent OSPF SPF calculations on R3 that cause a high CPU and packet loss on traffic traversing R3.

Discussion

Question 81

Refer to the exhibit.

Questions 81

The network administrator configured redistribution on an ASBR to reach to all WAN networks but failed Which action resolves the issue?

Options:

The route map must have the keyword prefix-list to evaluate the prefix list entries

The OSPF process must have a metric when redistributing prefixes from EIGRP.

The route map EIGRP->OSPF must have the 10.0.106.0/24 entry to exist in one of the three prefix lists to pass

EIGRP must redistribute the 10.0.106.0/24 route instead of using the network statement

Discussion

Question 82

Questions 82

Refer to the exhibit. A network administrator configured an IPv6 access list to allow TCP return traffic only, but it is not working as expected. Which changes resolve this issue?

Options:

ipv6 access-list inboundpermit tcp any any syndeny ipv6 any any log!interface gi0/0ipv6 traffic-filter inbound out

ipv6 access-list inboundpermit tcp any any syndeny ipv6 any any log!interface gi0/0ipv6 traffic-filter inbound in

ipv6 access-list inboundpermit tcp any any establisheddeny ipv6 any any log!interface gi0/0ipv6 traffic-filter inbound in

ipv6 access-list inboundpermit tcp any any establisheddeny ipv6 any any log!interface gi0/0ipv6 traffic-filter inbound out

Discussion

Ace

No problem! I highly recommend Cramkey Dumps to anyone looking to pass their certification exams. They will help you feel confident and prepared on exam day. Good luck!

Harris Dec 28, 2025

That sounds amazing. I'll definitely check them out. Thanks for the recommendation!

Ivan

I tried these dumps for my recent certification exam and I found it pretty helpful.

Elis Dec 28, 2025

Agree!!! The questions in the dumps were quite similar to what came up in the actual exam. It gave me a good idea of the types of questions to expect and helped me revise efficiently.

Norah

Cramkey is highly recommended.

Zayan Dec 22, 2025

Definitely. If you're looking for a reliable and effective study resource, look no further than Cramkey Dumps. They're simply wonderful!

Syeda

I passed, Thank you Cramkey for your precious Dumps.

Stella Dec 28, 2025

That's great. I think I'll give Cramkey Dumps a try.

Marley

Hey, I heard the good news. I passed the certification exam!

Jaxson Dec 5, 2025

Yes, I passed too! And I have to say, I couldn't have done it without Cramkey Dumps.

Question 83

Questions 83

Refer to the exhibit. An engineer has successfully set up a floating static route from the BRANCH router to the HQ network using HQ_R1 as the primary default gateway When the g0/0 goes down on HQ_R1, the branch network cannot reach the HQ network 192.168.20.0/24. Which set of configurations resolves the issue?

Options:

HQ_R3(config)# ip sla responderHQ_R3(config)# ip sla responder icmp-echo 172.16.35.1

BRANCH(config)# ip sla 1BRANCH(config-ip-sla)# icmp-echo 192.168.100.2

HQ R3(config)# Ip sla responderHQ R3(config)# Ip sla responder Icmp-echo 172.16.35.5

BRANCH(config)# Ip sla 1BRANCH(config-ip-sta)# Icmp-echo 192.168.100.1

Discussion

Page: 20 / 47

Title

Questions

Posted

cisco.freetechexam.full access 300-410 tutorials.by cobie.q318.vce.pdf

318