Cisco braindumps2go 300-425 Leak Questions by Kitty q68 vce pdf

Page: 16 / 21

Exam Name:	Designing Cisco Enterprise Wireless Networks (ENWLSD)
Exam Code:	300-425 Dumps
Vendor:	Cisco	Certification:	CCNP Enterprise
Questions:	286 Q&A's	Shared By:	kitty

Question 64

A customer has two locations named building 1 and building 2 Each location has a Cisco wireless network with these components

Building 1

• 2 Cisco Catalyst 9800 Series Wireless Controllers in a high availability cluster

• 50 Cisco Catalyst 9100 APs

• Contractor SSID in VLAN 100

• Corporate SSID in VLAN 200

• mobility group configured to the building 2 WLCs

Building 2

• 2 Cisco Catalyst 9800 Series Wireless Controllers in a high availability cluster

• 20 Cisco Catalyst 9100 APs

• Contractor SSID in VLAN 300

• Corporate SSID in VLAN 400

• mobility group configured to the building 1 WLCs

The customer has a new security requirement mandating that all contractor SSID traffic must terminate on VLAN 100 on the building 1 WLCs for all locations. Which design approach must the engineer take?

Options:

Use the building 2 WLCs as foreign controllers and building 1 as anchor controllers tor the contractor SSID traffic.

Use the building 2 WLCs as anchor controllers and building 1 as foreign controllers for the contractor SSID traffic.

Use the WLCs at both buildings as anchor controllers and tunnel the contractor SSID traffic to building 1.

Use the WLCs at both buddings as foreign controllers and tunnel the contractor SSI0 traffic to building.

Discussion

Question 65

Refer to the exhibit.

Questions 65

Client A is roaming from AP1 on WLC1 to AP2 on WLC2. The client roams between two APs registered to two different controllers. The WLAN on the two controllers is on a different subnet. Which scenario explains the client's roaming behavior?

Options:

The client database entry is different than that of Layer 2 roam. (Instead of cop-ying, it moves the database to the new controller.)

The client database entry is different than that of Layer 2 roam. (Instead of mov-ing, it copies the database to the new controller.)

The client database entry is different than that of Layer 2 roam because the cli-ent database is neither moved nor copied into the new controller.

The client database remains in the mobility anchor controller and it is not cop-ied or moved.

Discussion

Nadia

Why these dumps are important? Can I pass my exam without these dumps?

Julian May 31, 2026

The questions in the Cramkey dumps are explained in detail and there are also study notes and reference materials provided. This made it easier for me to understand the concepts and retain the information better.

Billy

It was like deja vu! I was confident going into the exam because I had already seen those questions before.

Vincent Jun 22, 2026

Definitely. And the best part is, I passed! I feel like all that hard work and preparation paid off. Cramkey is the best resource for all students!!!

Ace

No problem! I highly recommend Cramkey Dumps to anyone looking to pass their certification exams. They will help you feel confident and prepared on exam day. Good luck!

Harris Jun 2, 2026

That sounds amazing. I'll definitely check them out. Thanks for the recommendation!

Lennie

I passed my exam and achieved wonderful score, I highly recommend it.

Emelia Jun 15, 2026

I think I'll give Cramkey a try next time I take a certification exam. Thanks for the recommendation!

Question 66

Drag and drop the characteristics from the left onto the correct functionalities on the right.

Questions 66

Options:

Discussion

Question 67

An enterprise network administrator is asked to set up an experimental WLAN for a collaboration project with a local service provider. The WLAN must be anchored to a WLC in the service provider data center using legacy mobility mode. After the configurations are completed on the WLCs and the firewalls in the path, the data path mobility tunnel is failing to come up. What should be performed by the administrator to debug the issue?

Options:

Establish a Telnet connection from a local PC to the firewall on port 97.

Use the mapping command on the WLC.

Establish a Telnet connection from a local PC to the firewall on port 16666.

Use the mapping command on the WLC.