Pure Storage Updated FlashArray-Implementation-Specialist Exam Questions and Answers by lowri

For a Non-Disruptive Upgrade (NDU) from aFlashArray//Xto aFlashArray//XL, the upgrade kit typically contains4 QSFP cables, 2 Mellanox cards, and 20 DFMD blanks (or modules).

2 Mellanox Cards:The FlashArray//X (source) likely requires the installation of 100GbE RoCE adapters (Mellanox) into its controllers to establish the high-speed replication link with the new FlashArray//XL (which has 100GbE native). One card is installed per //X controller.

4 QSFP Cables:To ensure a redundant, high-bandwidth connection between the two arrays during the data migration phase, 2 cables are used per controller pair (CT0-to-CT0 and CT1-to-CT1), totaling 4 cables.

20 DFMDs (Blanks/Fillers):The FlashArray//X typically holds 20 DirectFlash Modules. The FlashArray//XL chassis has 40 slots. When the 20 data drives are physically moved from the //X to the //XL, the //XL will still have 20 empty slots. These must be filled with DirectFlash blanking modules (DFMD blanks) to maintain proper chassis airflow and thermal pressure. Thus, the kit includes these 20 fillers.

TheFlashArray//X20 R4operates with a minimum AC voltage input of approximately90 VAC.

The FlashArray//X series (specifically the entry-to-mid-range models like the X10, X20, and X50) utilizes high-efficiency Power Supply Units (PSUs) designed with auto-ranging capabilities. These PSUs conform to standard global power infrastructure requirements, supporting a nominal input range of100V to 240V AC(50/60 Hz).

Low-Line Support:Because the X20 is an entry-level enterprise array often deployed in diverse environments (including edge locations or standard office server rooms), it fully supports "low-line" power (100-120V nominal). The technical minimum tolerance for these power supplies typically extends down to 90 VAC to account for voltage sags or fluctuations.

Contrast with High-End:Larger, higher-density systems like the FlashArray//XL or fully loaded high-performance chassis configurations often require "high-line" power (200V-240V) to deliver sufficient wattage efficiently. However, the X20 R4 does not have this restriction. Therefore, Option A (90V) represents the correct minimum floor, whereas Options B and C represent high-line voltages that are supported but notrequiredfor minimum operation.

The commandpurenetwork listis used to identify the configuration and status of the array's logical network interfaces.

Command Output:Running purenetwork list provides a tabular view of all configured IP interfaces (Management, iSCSI, Replication). Critical columns in this output include:

Name:(e.g., vir0, eth0, eth1)

Address/Netmask:The IP configuration.

Gateway:Routing information.

Status:(e.g.,"enabled"or "disabled").

Usage:An Implementation Engineer uses this command to verify that the management VIP and physical interfaces are correctly configured and legally "up" (enabled) in the Purity software stack.

Distinctions:While purehw list is used forphysicalhardware link status (e.g., cable plugged in/link light), purenetwork is the primary namespace for IP-level validation. Options B and C (--all, --eth) are not the primary standard syntax for the general status view in this specific context; the base command provides the necessary summary data for initial verification.

TheFlashArray//XLsupports0 (zero)SAS expansion shelves for permanent capacity.

Architecture:The FlashArray//XL is architected exclusively forNVMestorage media. Its backend connectivity utilizes 100GbE RoCE (RDMA over Converged Ethernet) to connect toDirectFlash Shelves (DFS). It does not possess the legacy SAS controllers or ports required to drive SAS expansion shelves.

Migration Exception:While a "SAS Swing Shelf" (containing legacy SSDs from an older array) might be temporarily attached during a specific Data-in-Place upgrade migration scenario, this is a transient state. In terms ofsupportedoperational configuration for storage capacity, the limit is zero. The platform relies entirely on DirectFlash Modules in the chassis and external DirectFlash Shelves.

Contrast:Older generations (FlashArray//M, FlashArray//X R1/R2) supported SAS shelves, but the //XL platform eliminates this protocol entirely in favor of end-to-end NVMe.