Huawei Updated H12-893_V1.0 Exam Questions and Answers by gurbaaz

VXLAN (Virtual Extensible LAN) tunnels are used to encapsulate Layer 2 traffic over a Layer 3 network, a key component in Huawei’s CloudFabric data center solutions. Let’s evaluate each statement:

A. A VXLAN tunnel is identified by a pair of VTEPs:This is true. A VXLAN tunnel is identified by the pair of VXLAN Tunnel Endpoint (VTEP) IP addresses (local and remote), along with the VNI (VXLAN Network Identifier). This ensures unique tunnel identification.TRUE.

B. After a tunnel is established, if one end of the tunnel goes Down, the other end may not go Down:This is true. VXLAN tunnels are unidirectional, and the status of one end does not automatically affect the other unless the underlay network connectivity (e.g., Layer 3 reachability) is lost. The remote VTEP may remain operational if it can still encapsulate/decapsulate traffic.TRUE.

C. For a static tunnel, you need to manually configure the local and remote VNIs:This is true. In a static VXLAN tunnel, administrators must manually configure the VNI and VTEP IP addresses on both ends, as there is no dynamic control plane (e.g., BGP EVPN) to automate the process.TRUE.

D. Dynamic tunnels depend on EVPN Type 5 routes to transmit information:This is false. Dynamic VXLAN tunnels rely on BGP EVPN as the control plane, but Type 5 routes (IP Prefix routes) are specifically used for advertising host IP routes and external network routes, not for general tunnel establishment. Dynamic tunnel setup primarily uses Type 2 (MAC/IP Advertisement) and Type 3 (Multicast) routes to exchange VNI and VTEP information. Type 5 routes are relevant for Layer 3 routing, not the initial tunnel setup.FALSE.

Thus,Dis the false statement because dynamic tunnels depend on EVPN Type 2 and Type 3 routes, not Type 5, for initial establishment.References:Huawei CloudFabric Data Center Network Solution – VXLAN Configuration Guide; HCIP-Data Center Network Training – VXLAN Tunneling.

Huawei’s iMaster NCE-Fabric is an SDN controller for the CloudFabric data center network solution, providing network management and automation. The rollback feature allows administrators to revert configuration changes to previous states in case of errors. According to Huawei’s documentation, iMaster NCE-Fabric supportsfour rollback levels, enabling the system to store and restore up to four previous configuration versions. This ensures flexibility in undoing changes during network management tasks like upgrades or policy adjustments.

Options Analysis:

A. 3: Incorrect, as it underestimates the supported levels.

B. 4: Correct, aligning with Huawei’s specified rollback capability.

C. 2: Incorrect, as it is fewer than the supported levels.

D. 1: Incorrect, as it limits rollback to a single state, which is insufficient for complex management.

Thus, the answer isB (4).References:Huawei CloudFabric Data Center Network Solution – iMaster NCE-Fabric Features; HCIP-Data Center Network Training – SDN Controller Management.

EVPN (Ethernet VPN) is a control plane technology used with VXLAN to provide Layer 2 and Layer 3 services in data center networks, including Huawei’s implementations. EVPN routes are categorized into types, with Type 5 routes (IP Prefix routes) serving a specific purpose:

Type 5 Routes:These routes advertise IP prefixes and are used for inter-subnet routing, allowing communication between different VXLAN Virtual Network Identifiers (VNIs) or between VXLAN networks and external networks. They carry a Layer 3 VNI and IP prefix information, enabling routers or gateways to perform Layer 3 forwarding.

Usage Scope:Type 5 routes are not limited to hosts on a VXLAN network accessing external networks. They are also used by network devices (e.g., gateways, routers) within the EVPN domain to facilitate routing between subnets, including intra-VXLANcommunication. For example, a centralized gateway or distributed gateway can use Type 5 routes to route traffic within the data center or to external networks, not just host-initiated access.

The statement isFALSE (B)because Type 5 routes are not exclusively for hosts on a VXLAN network to access external networks; they support broader Layer 3 routing functions across the EVPN domain.References:Huawei HCIP-Data Center Network Training – EVPN Routing; CloudFabric EVPN Configuration Guide.

In Huawei’s CloudFabric Solution, Virtual Private Clouds (VPCs) enable isolated network environments, and interworking scenarios involve traffic between VPCs. The statement claims that traffic is checked and filtered only by the firewall in the source or destination VPC. Let’s evaluate:

VPC Interworking:Traffic between VPCs can be routed via a gateway (e.g., a Layer 3 gateway or centralized router) and may involve multiple security checkpoints depending on the design. Firewalls can be deployed in the source VPC, destination VPC, or a centralized location (e.g., a service chain or border gateway).

Firewall Role:The statement implies exclusivity (only one firewall), but in practice, traffic may be filtered by firewalls at both ends, a centralized firewall, or additional security devices (e.g., VAS nodes) in the path. For example, inter-VPC traffic might pass through a firewall in the source VPC for egress filtering and another in the destination VPC for ingress filtering, or a shared firewall in a hub-and-spoke model. Huawei’s security architecture (e.g., with SecoManager) supports distributed or centralized filtering, not limited to a single VPC’s firewall.

The statement isFALSE (B)because traffic is not restricted to being checked and filtered only by the firewall in the source or destination VPC; multiple firewalls or security devices may be involved.References:Huawei CloudFabric Data Center Network Solution – VPC Interworking; HCIP-Data Center Network Training – Security Design.