Black Friday VIP Weekend - 75% Discount offer - Ends in 0d 00h 00m 00s - Coupon code: 75brite

Netapp Updated NS0-094 Exam Questions and Answers by elisei

Page: 3 / 5

Netapp NS0-094 Exam Overview :

Exam Name: NetApp Hardware Support Engineer Professional Exam
Exam Code: NS0-094 Dumps
Vendor: Netapp Certification: NAHSE
Questions: 81 Q&A's Shared By: elisei
Question 12

You have replaced a failed boot device. You perform boot_recovery and receive no errors. However, when the node reboots, it reports that it has no disks.

What are two possible causes? (Choose two.)

Options:

A.

The SAS cables were incorrectly reconnected after reinstalling the motherboard.

B.

The disks that are owned by this node have been marked as failed.

C.

The node is booting a lower version of ONTAP software than was last used.

D.

The interconnect is down.

Discussion
Question 13

You have replaced the cluster backend switches on a 4-node NetApp ONTAP cluster with new switches. After the replacement, you realize that the system shows errors for the old switches that were removed:

Questions 13

You also notice that system switch ethernet show shows four switches, the two old switches and the two new switches.

What action will resolve the issue?

Options:

A.

Perform a reboot of the affected node using the storage failover takeover command.

B.

Delete the old switches from the database using the system switch ethernet delete command.

C.

Clear the health alert using the system health alert delete command.

D.

Reconnect the old switches and download a support bundle using the system switch ethernet log collect command.

Discussion
Question 14

You have a NetApp ONTAP cluster that is serving both SMB over 10Gbe and FC data. An application owner has started to complain about poor performance and asks you to research the issue. When looking through EMS messages, you see the following output:

Questions 14

Which defective component triggers the EMS message?

Options:

A.

10Gbe module

B.

fiber cable

C.

32G FC module

D.

adapter card in slot 2

Discussion
Freddy
I passed my exam with flying colors and I'm confident who will try it surely ace the exam.
Aleksander Oct 22, 2026
Thanks for the recommendation! I'll check it out.
Ernest
That's amazing. I think I'm going to give Cramkey Dumps a try for my next exam. Thanks for telling me about them! CramKey admin please share more questions……You guys are amazing.
Nate Oct 12, 2026
I failed last week, I never know this site , but amazed to see all these questions were in my exam week before. I feel bad now, why I didn’t bother this site. Thanks Cramkey, Excellent Job.
Miriam
Highly recommended Dumps. 100% authentic and reliable. Passed my exam with wonderful score.
Milan Oct 22, 2026
I see. Thanks for the information. I'll definitely keep Cramkey in mind for my next exam.
Melody
My experience with Cramkey was great! I was surprised to see that many of the questions in my exam appeared in the Cramkey dumps.
Colby Oct 22, 2026
Yes, In fact, I got a score of above 85%. And I attribute a lot of my success to Cramkey's dumps.
Lennie
I passed my exam and achieved wonderful score, I highly recommend it.
Emelia Oct 23, 2026
I think I'll give Cramkey a try next time I take a certification exam. Thanks for the recommendation!
Question 15

You are replacing a boot device on a FAS8300 system that is running ONTAP 9.10P6 software. You attach a USB memory stick to the external USB port on the storage controller but cannot access the memory stick.

What step needs to be performed to access the boot device?

Options:

A.

Set the port to “enabled” with setenv.

B.

You need to use ONTAP 9.11 or later software.

C.

Add the boot device before the BIOS is loaded.

D.

The external USB port is not activated on NetApp systems.

Discussion
Page: 3 / 5

NS0-094
PDF

$27.5  $109.99

NS0-094 Testing Engine

$32.5  $129.99

NS0-094 PDF + Testing Engine

$42.5  $169.99