Juniper transcender jncip-sec Jn0-637 Exam Questions And Answers Pdf by Caelan q52 vce pdf

Page: 8 / 8

Juniper JN0-637 Exam Overview :

Exam Name:	Security, Professional (JNCIP-SEC)
Exam Code:	JN0-637 Dumps
Vendor:	Juniper	Certification:	JNCIP-SEC
Questions:	115 Q&A's	Shared By:	caelan

Question 32

You have a multinode HA default mode deployment and the ICL is down.

In this scenario, what are two ways that the SRX Series devices verify the activeness of their peers? (Choose two.)

Options:

Custom IP addresses may be configured for the activeness probe.

Fabric link heartbeats are used to verify the activeness of the peers.

Each peer sends a probe with the virtual IP address as the destination IP address.

Each peer sends a probe with the virtual IP address as the source IP address and the upstream router as the destination IP address.

Discussion

Answer:

A, D

Explanation:

Comprehensive Detailed Step-by-Step Explanation with All Juniper Security References

Understanding the Scenario:

Multinode HA Default Mode Deployment:

In a chassis cluster, two SRX devices operate together to provide high availability.

ICL (Inter-Cluster Link) is Down:

The control and fabric links between the nodes are not operational.

Objective:

Determine how the SRX devices verify each other's activeness without the ICL.

Option A: Custom IP addresses may be configured for the activeness probe.

Explanation:

When the control link is down, SRX devices use an ICMP ping-based activeness probe to check the peer's status.

Custom IP addresses can be configured as probe targets to verify the peer's activeness.

[Reference:, "You can configure the SRX Series device to send activeness probes to a configured IP address to verify the peer's state when the control link is down.", Source: Juniper Networks Documentation - Control Link Failure Detection, Option D: Each peer sends a probe with the virtual IP address as the source IP address and the upstream router as the destination IP address., Explanation:, The SRX devices send ICMP probes to an upstream device using the redundancy group's virtual IP address as the source., This helps determine if the peer node is still active by verifying network reachability., Reference:, "When the control link fails, each node sends ICMP pings to the configured probe addresses using the redundancy group's virtual IP address as the source.", Source: Juniper Networks Documentation - Chassis Cluster Control Link Failure, Why Options B and C are Incorrect:, Option B: Fabric link heartbeats cannot be used because the ICL (which includes the fabric link) is down., Option C: Probes are sent to upstream devices, not using the virtual IP address as the destination., Conclusion:, The correct options are A and D because they accurately describe how SRX devices verify activeness without the ICL., ]

Billy

It was like deja vu! I was confident going into the exam because I had already seen those questions before.

Vincent Feb 23, 2026

Definitely. And the best part is, I passed! I feel like all that hard work and preparation paid off. Cramkey is the best resource for all students!!!

Sam

Can I get help from these dumps and their support team for preparing my exam?

Audrey Feb 15, 2026

Definitely, you won't regret it. They've helped so many people pass their exams and I'm sure they'll help you too. Good luck with your studies!

Georgina

I used Cramkey Dumps to prepare for my recent exam and I have to say, they were a huge help.

Corey Feb 24, 2026

Really? How did they help you? I know these are the same questions appears in exam. I will give my try. But tell me if they also help in some training?

Madeleine

Passed my exam with my dream score…. Guys do give these dumps a try. They are authentic.

Ziggy Feb 1, 2026

That's really impressive. I think I might give Cramkey Dumps a try for my next certification exam.

Question 33

You want to configure the SRX Series device to map two peer interfaces together and ensure that there is no switching or routing lookup to forward traffic.

Which feature on the SRX Series device is used to accomplish this task?

Options:

Transparent mode

Secure wire

Mixed mode

Switching mode