Cisco Updated 300-110 Exam Questions and Answers by ishaq

In Ekahau Site Survey, when planning a warehouse deployment using patch (directional) antennas, the antenna downtilt setting is the critical adjustment made when placing simulated APs on the floor plan map. Patch antennas have a defined radiation pattern with a main lobe that must be aimed precisely at the intended coverage zone. In a warehouse environment, APs with patch antennas are typically wall-mounted and aimed down aisles. The downtilt angle determines the vertical component of the antenna ' s aim — adjusting the downtilt in Ekahau tilts the simulated antenna ' s main radiation lobe downward toward the warehouse floor and the working zone of RF scanner devices, rather than projecting RF energy horizontally at an ineffective angle. Ekahau allows engineers to specify the horizontal and vertical orientation of the antenna in three dimensions, and the downtilt value directly controls how the software models the antenna ' s coverage pattern in the vertical plane. AP channel (Option A) is set during channel planning, not during AP placement. Wi-Fi technology (Option B) determines the modulation and protocol standard but is set as an AP property. AP transmission power (Option D) controls cell radius but is set separately from antenna orientation. Reference: WLSD Study Guide — Ekahau Predictive Survey, Directional Antenna Configuration, Warehouse RF Design and Antenna Orientation.

Cisco 3800 Series APs support IEEE 802.11ac Wave 2, which can deliver throughput exceeding 1 Gbps. Fast Ethernet switches are limited to 100 Mbps per port, creating a severe bottleneck. The two actions that provide maximum support are replacing with mGig switches (Option A) and replacing with gigabit switches with 10G uplinks (Option B). mGig (Multi-Gigabit Ethernet) switches support 2.5G and 5G speeds over existing CAT 6A cabling, allowing the full throughput of 802.11ac Wave 2 APs to be utilized without replacing the existing cable plant. Gigabit switches with 10G uplinks ensure that the access layer can support 1 Gbps per AP port while providing sufficient uplink capacity. Since the existing cabling is already CAT 6A, which supports 10 Gbps over short distances and 5 Gbps over 100 meters, there is no need to replace the wiring (Option D eliminates). The 100-meter distance limitation (Option C) already applies to standard Ethernet and is met by CAT 6A — this is not an action but a constraint check. Option E (55 meters) is only relevant for specific 5GBASE-T configurations and doesn ' t maximize support compared to A and B. Reference: WLSD Study Guide — mGig Infrastructure, 802.11ac Wave 2 Infrastructure Design, Switch Upgrade Planning.

The command ' debug mobility handoff enable ' is used to validate the mobility control packets between Wireless LAN Controllers (WLCs). This command enables debugging of the handoff process, which is critical for ensuring seamless client roaming between controllers. When WLCs are separated by firewalls, it is essential to confirm that mobility control packets can traverse these firewalls without being dropped or rejected. The ' debug mobility handoff enable ' command allows network administrators to monitor the handoff process in real time and identify whether mobility PDUs are being exchanged successfully. If mobility control packets are being blocked by the firewall, this debug output will show failures in the handoff sequence. This command directly validates bidirectional mobility traffic flow, making it the correct troubleshooting tool for the scenario described. Options A and D are not valid Cisco WLC commands. Option C enables configuration-level mobility debugging but does not specifically validate handoff packet flow. Reference: WLSD Study Guide — Mobility Troubleshooting, Debug Commands, Inter-Controller Roaming Validation.

Floor loss calculation is a fundamental skill in multi-floor wireless site survey methodology. The floor attenuation value represents the signal power reduction caused by penetrating through a single floor structure including the floor decking, subfloor, ceiling material, plenum space, and any structural elements. In this measurement scenario, the engineer has two data points: -45 dBm measured at the ground level of the floor containing the access point (the signal level just below the AP ' s floor) and -50 dBm measured at the ceiling level of the floor below (the signal level just after passing through the floor structure). The floor loss is simply the difference between these two measurements: (-45 dBm) - (-50 dBm) = -45 + 50 = 5 dB. The result is expressed as a positive value (5 dB) representing attenuation — signal power decreases by 5 dB when passing through the floor. Expressing it as -5 dB (Option B) would incorrectly imply a signal gain. The 95 dB values (Options A and D) result from incorrectly adding rather than subtracting the dBm values — a common error when working with negative dBm figures. This floor attenuation value (5 dB) would then be entered into Ekahau ' s floor material properties to improve predictive model accuracy. Reference: WLSD Study Guide — Multi-Floor Signal Propagation, Floor Attenuation Factor (FAF), Ekahau Floor Loss Measurement Methodology.